Author: admin

1. What drawing shows the locations of walls and the sizes
of rooms?
2. For frame construction, are exterior walls usually
dimensioned from the outside of the wall, the centerline of the wall, or the
inside of the wall?
306:
1. What drawing shows the location of plumbing fixtures?
2. Are dimensions for concrete walls usually taken from the
centerline of the wall or the face of the wall?
3. What is the inside width of the linen closet at the end
of the hall?

1. What are the inside dimensions of bedroom #2?
2. What is the thickness of the partitions between bedroom
#3 and the hall?
3. What is the thickness of the interior wall between
the powder room and the stairs?

1. What is an elevation drawing?
2. What is indicated by a heavy solid line near the bottom
of a building on an exterior elevation?
3. What is indicated by dashed lines near the bottom of a
building on an exterior elevation?

1. Which elevation is the north elevation?
2. In what compass direction does the left end of the house
face?
3. What is the dimension from the surface of the floor to
the ceiling?

1. What is used to show the detail of a complex design, installation, or product?
2. What kind of section drawing is the Section 2?
3. What kind and size of material is to be used for the foundation walls?

1. What is used between the foundation wall and the 2 * 10
floor joists?
2. What kind and size of insulation is used around the
foundation? Is this used on the inside or outside of the foundation?
3. What is the distance from the kitchen countertop over the
dishwasher to the bottom of the wall cabinets?

1. What is the width and height of the cabinet above the
oven?
2. Which wall is the oven on—north, south, east, or west?
3. What size studs are used in a typical interior wall?
4. What is done in the coat closet to create headroom over
the stairs?

PART THREE- DETAILED WRITE-UP INSTRUCTIONS
The Bachelor Dissertation report should constitute a well-structured and convincing account of a study. The projects are assessed on 3 main elements, form, structure and content. This section briefly describes the nature of each of these elements.
Concerning FORM, a. TYPING, PAGE SIZE AND LENGTH The report must be typed on A4 (29.7 cm x 21 cm) paper and be 1.5 spaced. Pages should be typed on one side only. The main text should be in 12-point type and headings should be larger.
b. SUB-SECTIONS AND NUMBERING The decimal numbering system should be adopted. Sub-sections should have some distinguishable heading.
c. PAGE NUMBERS
Page numbers before the main body of the text, i.e. before chapter 1 begins, are in lower case roman numerals, i.e. i, ii, Hi, iv, v, etc. The main body of the text should use normal Arabic numerals, i.e. 1,2,3,4, etc., starting at chapter 1. Appendices may continue the main body numbering or use a different numbering system perhaps distinguished by a prefix, such as Al, A2, A3.
d. TABLES AND ILLUSTRATIONS
Photographs, maps, graphs, tables and other illustrations should be placed as close as possible to where they are referenced or described in the text. Each table and illustration should have a unique reference number and be referred to in the text. Sources and dates should be clearly identified.
e. PROJECT TffLE
The title should describe the content of the project accurately and concisely. It should be written as a question.
f. STYLE
The style of writing should be passive and indirect (eg -The following recommendations can be made” instead of -I recommend the following..” . References should be used appropriately in order to distinguish what the AUTHOR did and what OTHERS did.
g. TITLE PAGE
The title page gives the following information in the order listed:
Attachments:
5962652_1_48eec190-638e-4400-9ddd-b54a6f3d7c4a.jpeg
5962652_2_6b179ccc-3185-4583-9e22-fea4692e7d9a.jpeg
5962652_3_ef195510-012d-471f-a044-43cf39c0528e.jpeg
5962652_4_12733394-2426-42f5-8ca9-84d6da17db12.jpeg
5962652_5_3b012573-397e-418f-a5b6-f0b3df77b24b.jpeg